10 Quick Tips About Audi G28
How to Replace an audi spare key replacement G28 Engine Speed Sensor
Charles the Humble Technician shows how to replace the G28 Engine Speed Sensor. The sensor is located at the edge of transmission over the flywheel gear. It sends a signal to the ECU via an uncolored wire (T55/49) which is then sent to the tachometer within the instrument cluster.
1. Engine Speed Sensor
The grey wire is located at the edges of the transmission, just above the flywheel ring. This sensor sends an electrical signal through the grey wire to pin T55/49. The ECU utilizes this information to control fuel and boost. It also sends signals to the G5 tachometer inside the instrument cluster.
The sensor serves as a reference point to connect with the G40 Camshaft Position Sensor. The ecu needs to know when the crankshaft is TDC and the location of the camshaft so it can activate spark and injectors accordingly.
If this sensor fails, the ECU will display a P00160 code which means the Crank Shaft and Intake Camshaft are out of sync and could indicate the chain stretching or a jump link on the upper chain of timing. However, the error code won't appear on its own, without additional information from other sensors (G4 and G40).
It is a little tricky to test because there are different pins on the connector, and they all have different functions. The most effective method to test it is by measuring the resistance between the ECU and the sensor. It should read approximately 1000 ohms when it is in full operation. If you're having issues with this sensor, look for evidence of coolant or oil in the connector bay.
2. Injectors
Yesterday, while accelerating from the highway paytoll at full speed I noticed a significant reduction in power. It was like the engine was running out of gas. Or my injectors weren't firing. In the morning, i removed the spark plugs, 3 were drenched with gazoline the fourth one was dry. When I start the engine without sparks, I put a piece of tissue on the top of each of the injector holes and the 3 that were drenched in gazoline pop out, but the 4th stays closed. I tried to test the ground connections of ECU pins 14,30, and 48/55. I found zero ohm. So i assume the problem is elsewhere.
I also tried to reset PID without success. The car can start when the G28 is unplugged and it runs perfectly when it is connected but it still is experiencing intermittent misfires at higher RPM. The temperature sensor for coolant (G62) shows the wrong temperature value of -49c, even if I unplug it. I also noticed that the gauge for oil pressure in the cockpit is showing 2 bar, whereas the actual pressure is 0.0 when I crank up the engine.
I don't know what to do. I think I've eliminated everything else. I'm worried that i might have missed something. If anyone has suggestions, please let me know! TIA!
3. Fuel Pump
The fuel pump in the g28 can be activated by a signal from the RPM sensor. The GM-style sender is identical to the G4 and both function in the 80 100, 200, UrS and RS2 cars which is why you can easily locate one at a salvage yard or in a local parts store. It is simple to test them: simply switch your DMM into resistance mode and determine the distance between pins 1 and 2 (with the bump on the connector's edge facing up). They must be infinite Ohms.
4. ECU
Our 20vt turbo (3B, AAN, ABY and ADU) engines are equipped with an ECU that must know the position and speed of the crankshaft to make decisions about fuel injector timing etc. To accomplish this, it utilizes a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If either of these sensors go badly, you will see codes on the diagnostic scanner which could cause engine shut down.
A failing G28 sensor could cause an inaccurate gearbox speed counter and a gearbox which shifts faster than normal, and/or a misfire in the gear. It is probable that your sensor is failing and requires to be replaced if you notice any of these symptoms. They are cheap and easy-to-find, especially when they're an Bosch unit like ours. Alternatively, GM's version of this part would be a good option.
5. Tachometer
A damaged engine sensor could cause a variety of issues in your vehicle. It is an important part of the transmission of your audi replacement key service near me because it relays information to the ECU regarding how fast or slowly the engine is turning. If the sensor fails, it could affect the performance of the transmission and the other car's components.
The G5 engine sensor is located near the edge of the transmission, over the flywheel ring. It sends a signal via gray wire to ECU pin T55/49. The ECU then uses and processes this signal to control fuel, timig and boost as well as transmitting it to the G5 tachometer inside the instrument cluster. You can determine if the sensor is in failure by examining the continuity of the sensor to the tachometer. You can also verify continuity between pin T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79]) and between pin T6a/1 and pin T26a/12. You should observe approximately 1000 ohms resistance between those two pins. This is a standard part that is found across the audi key fob not working Car Key Holder (Historydb.Date) 80 100, 200, UrS and RS2 range from 1985 MC until the 1997 UrS AAN and 1995 RS2 ADU. Good parts could be found in wrecking yards.