Three Greatest Moments In Audi G28 History
How to Replace an audi replacement key G28 Engine Speed Sensor
In this video Charles the Humble Mechanic demonstrates how to replace the G28 engine speed sensor. This sensor is located near the edges of the transmission above the flywheel ring gear. It sends a signal to the ECU via the grey wire (T55/49) and then to the tachometer within the instrument cluster.
1. Engine Speed Sensor
The grey wire is located at the edges of the transmission, above the flywheel ring. The sensor sends an electrical signal through the grey wire to pin T55/49. The ECU utilizes this information to control fuel and boost. It also sends an indicator to the G5 Tachometer in instrument cluster.
The sensor is used as a reference for comparing with the G40 Camshaft Position Sensor. The ecu needs to know when the crankshaft reached TDC, and where the camshaft lies so that it can activate the spark and injectors.
If this sensor fails when it fails, the ECU will display an error code P00160. This indicates that the Crank Shaft is out of sync with the Intake Camshaft. It could also indicate a chain stretch or a jumped chain link in the upper chain. However, the error code won't be displayed on its own without additional information from other sensors (G4 and G40).
It's a bit tricky to test because there are different pins on the connector, and each has its own functions. The best method for doing this is to measure the resistance between the ECU and the sensor. It should read approximately 1000 ohms when it is in full operation. Examine for evidence of coolant or oil in the connector bay if there are issues with this part.
2. Injectors
Yesterday, when i was accelerating to the fullest speed from highway paytoll, I experienced massive power loss like the engine is out of gas or the injectors aren't firing any more. I pulled out the spark plugs this morning, three were soaked in gasoline, and the fourth was unclean. When i crank the engine with no sparks, I put a piece of tissue on top of each injector hole and the 3 drenched with gazoline jump out but the 4th stays shut. I checked the ground connection on ECU pins 14/55,30/55 and 48/55 I get zero Ohm. I'm assuming the issue is somewhere else.
I also tried to reset the PID but with no luck. The car is able to start when the G28 is not plugged in and is running fine when it is plugged in, but still has the intermittent misfire issue at higher RPM. The coolant sensor (G62) even when it is unplugged, shows temperatures of -49c. Also i noticed that the oil pressure gauge in the cockpit shows 2 bar when the actual pressure is 0.0 when I crank up the engine.
I'm not sure what to do. I think I've all other possibilities out. I'm concerned that i may have missed something. If anyone has any ideas please share them! TIA!
3. Fuel Pump
The fuel pump in the g28 is activated by a signal sent by the RPM sensor. The GM-style sensor is identical to the G4 and both are used in the 80, 100 200, UrS and RS2 cars which is why you can easily locate one at a salvage yard or in a local parts store. It is simple to test them by putting your DMM in resistance mode and measure the resistance between pins 1 (with the bump on the connector's side up) and 2 (2nd from the left on the black connector's side). They should be infinite Ohms.
4. ECU
Our 20vt turbo (3B, AAN, ABY and ADU) engines have an ECU that has to be aware of the speed and position of the crankshaft in order to make decisions regarding timing of the fuel injectors, etc. It uses a Crank Position Sensor G4 and an Engine Speed Sensor G28 to accomplish this. If either of these sensors go badly, you will see codes on the diagnostic scanner which can lead to engine shutdown.
A damaged G28 sensor could result in an inaccurate gearbox speed counter, a gearbox that shifts faster than normal, or an unfire when in the gear. It is likely that the sensor is failing and needs to be replaced if you encounter any of these symptoms. They're inexpensive and easy to locate particularly when they're an Bosch unit like ours. You can also choose the GM version of this part is also a great option.
5. Tachometer
A malfunctioning engine sensor audi connect key (https://g28carkeys59787.wizzardsblog.com) can cause a myriad of issues within your vehicle. It's an essential component of the audi tt Replacement key's transmission because it communicates to the ECU about how fast or slow the vehicle's crankshaft is rotating. When this sensor fails, it can affect the performance of the transmission as well as the rest of the car's components.
The G5 engine sensor is located at the outskirts of the transmission, over the flywheel ring. It sends a signal via gray wire to ECU pin T55/49. The ECU then processes the signal to control the flow of fuel, timig and boost and then transmitting it to the G5 tachometer in the instrument cluster. You can determine if the sensor is in failure by examining the continuity of the sensor to the tachometer. Additionally, you can verify continuity between pin T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79trace [79]), and between pin T6a/1 and pin T26a/12. You should observe approximately 1000 ohms resistance between those points. This is the same across the audi a5 key fob 80-100-200-RS2 model, ranging from the 1985 MC all the way up to the 1997 UrS AN and the 1995 RS2 Du So, you may find them in wrecking yards.